Pars I: inspectionem ante institutionem
1. Orbis die inspectionem ante installation
Utrum opus superficies est etiam.
Sive sulcus confectus et utrumque foraminis confringetur.
Utrum dia foraminis et compressionem RATIO rectam
Sive non sunt dent aut induendum marcas in upupam et attenuatis superficies, ut ostensum est in Figura I et II.
II. Rollerus inspectionem ante institutionem
Utrum componentes gyrationis est normalis
Utrum ripam cylindro est
Utrum dens figura est completum
III. Reprehendo ad gerunt conditione upupam, et reponere in ineffective upupam in tempore
IV. Reprehendo ad induendum ad monteming superficies in coegi ora, et reponere in defecit coegi Rim in tempore
V. Reprehendo et adjust angulum de ramis ad vitare inaequaliter propagationem de materia
VI. Utrum installation foraminis pascit pyramidis pyramis laedi vel non
Pars II: Requirements pro Orbis Die installation
I. obstringere omnes nuces et seras symmetrrically ad requiritur torque
-Sz LH SSOX LXX LXX (DC exemplar), ut per exemplum, in anulus die densis Torque est XXX 0 N. M, Fengshang-Sz LH535 X1 XC Granulator tenens Box fulmine Tightening in Figura III; Cum pyramidis anulus mori installed, finis faciem in anulus mori debet esse in 0,20 mm, ut ostensum est in Figura IV.
2. When the cone ring die is installed, the clearance between the end face of the ring die and the end face of the drive wheel flange is 1-4mm, as shown in Figure 5, if the clearance is too small or there is no clearance, the drive rim must be replaced, otherwise the fastening bolts may be broken or the ring die may be broken.
III. Cum installing upupam circulum mori, cincinno omnes nuces et seras symmetrica secundum requiritur torque, et ut inter se inter se tenens arca archa sunt aequales in densis inter se tenens arca esse aequales in densis inter se tenens buxum esse aequales in densis inter se tenens arca, pares in densis. Uti feideler METIOR ad metimur gap inter interiore imo superficiem tenens arca et exteriores superficies circulum die tenens arca (plerumque 2-10mm). Sicut ostensum est in Figura VI, si gap est parva vel non est gap, et tenens arca debet reponi.
IV. Mori volvens gap sit inter 0.1-0.3 mm et temperatio potest fieri per visual inspectionem. Cum anulus mori conuertitur, melius est quod volvens est non circumducitur. Cum nova mori adhibetur, praesertim cum anulus mori cum parva mori foraminis adhibetur, mori volvens gap est solet augeri et ne calenderer-in tempore mori et vitare in calendereroni in tempore mori Bell oris.
V. Post annulum morietur, installed, reprehendo an cylindro est ora-pressed
Pars III: Annuli mori repono et sustentationem
I. Et anulus mori debet repono per siccum et munda et notatum cum cubits.
II. Nam in anulus mori non propter longo tempore, commendatur ad tunicam superficiem cum iacuit anti-rubigo oleum.
III. Si mori foraminis circulum morietur per materiam, placere uti modum olei immersionem vel coctione ad mollire materiam, et rursus granulatum.
IV. Cum autem circulum morietur pro magis quam VI menses, et oleum intus necessitates impleatur.
5. After the ring die has been used for a certain period of time, regularly check whether there are local protrusions on the inner surface of the ring die, and check whether the die hole guide port is ground, sealed or turned inward, as shown in Figure 8. If found, the ring die is repaired to prolong the service life, as shown in Figure 9. When repairing, it should be noted that the lowest part of the working inner surface of the ring die should be 2 mm above the bottom of the Overtravel sulcus, et non est adhuc temperatio prebenda pro volubilem eccentricum sagittam post reparatione.