Share to:

Hot Selling for Feed Milling Process Flow - Manufacturer of PTN Series Ring Die for Pellet mill spare parts – Zhengyi

Inquire

Model:
Brand: SHH.ZHENGYI

Product Detail

Product Tags

Feedback (2)

We know that we only thrive if we will guarantee our combined cost competiveness and high-quality advantageous at the same time for Diy Feed Pellet Mill , Single Shaft Paddle Mixer , Feed Pellet Making Machine , Welcome to make contact with us if you're fascinated inside our product, we are going to provide you with a surprice for Qulity and Value.

Hot Selling for Feed Milling Process Flow - Manufacturer of PTN Series Ring Die for Pellet mill spare parts – Zhengyi Detail:

● PTN series ring die

PTN Pellet mill ring die3
ptn

PTN pellet mill series ring die is made of high-quality alloy steel or high-chromium stainless steel (German standard X46cr13). It is processed by forging, cutting, drilling, heat treatment and other processes. Through strict production management and quality system, the hardness, die hole uniformity and die hole finish of the production ring die have reached very high quality.

Parameter

S/N	Model	Size ODIDoverall width*pad width -mm	Hole size mm
1	PTN450	560450180*106	1-12
2	PTN580	680580216*140	1-12
3	PTN650	791650245*175	1-12

Analysis of Abnormal Situation and Recommended Improvements
Reason Analysis for Broken (normally occurred in
continuous casting of small enterprises)

1. Die broken by drive wheel matching surface
2. Die broken by wearing and deformation of die lining ring.
3. Die broken by waring of driving key.
4. Indentation impressed on the surface of the die for the weakening effect of the de-ironing device, and then cause die to crack.
5. Small opening between the die and the compression roller.
6. Die broken by small compression ratio, small diameter fish feed die without pressure-relief vent.

No.	Appearance	Reasons	Solutions
1	Particle bends, with cracks	The dearance between the cutter and the die is too long. And the cutter is too blunt. The flour is too rough. The feeds are too hard. Remove the cutter or replace the cutter. Increase grinding fineness. Increase effective length of the die hole. Add syrup and oil.
2	With transversal crack	The fiber is too long. The conditioning time is too short. The humidity is too high. Control fiber fineness Prolong conditioning time. Control raw material temperature and reduce conditioning moisture.
3	Vertical cracks	The raw materials have elasticity that would expand after pressed. Too much moisture, crack occurs during cooling. Remain too long in the die hole. Improve the formula and increase feed density. Use dry saturated steam for conditioning. Increase effective length of the die hole.
4	Radiative cracks	Large particles exist (half an oorn or whole corns left)	Control the fineness of raw materials, increase grinding evenness.
5	Surface unevenness	Mix with large raw material particles, no sufficiently conditioned and softened With bubbles in the steam, bubble breaks and hole occurs after pelleting. Control the fineness of raw materials, increase griding evenness. Improve steam quality.
6.	Whisker like pellet	Too much steam and too large pressure, pellet cracks when left the die.	1. Reduce steam pressure, use low-pressure steam (15 – 20psi)for conditioning. 2. Check the position of the reducing valve.

ptn010
ptn09

Product detail pictures:

Related Product Guide:

It is our responsibility to meet your needs and efficiently serve you. Your satisfaction is our best reward. We are looking forward to your visit for joint growth for Hot Selling for Feed Milling Process Flow - Manufacturer of PTN Series Ring Die for Pellet mill spare parts – Zhengyi , The product will supply to all over the world, such as: Turkey , Doha , Belarus , With a wide range, good quality, reasonable prices and stylish designs, our solutions are extensively used in beauty and other industries. Our solutions are widely recognized and trusted by users and can meet continuously changing economic and social needs.

Andritz Pellet Mill